- 欧姆龙继电器G8G-1A7R 面议
- 欧姆龙继电器G8NW-27U 面议
- 欧姆龙继电器G8ND-27S 面议
- 欧姆龙继电器G8NW-2U 面议
- 欧姆龙继电器G8NW-2L 面议
- 欧姆龙继电器G8NW-2F 面议
- 欧姆龙继电器G8NW-2-M 面议
- 欧姆龙继电器G8QN-1A 面议
- Allen-Bradley 监控安 面议
普通会员
¥550.00/个
¥65.00/个
¥599.00/个
¥59.00/个
产地 | 中国 |
---|---|
是否进口 | 否 |
工作电源 | 15V-28V |
探测方式 | 烟雾探测 |
环境温度 | -10℃~+50℃(℃) |
环境湿度 | ≤95%RH(40℃±2℃)(%) |
使用范围 | 烟雾粉尘少的场所 |
3C证书编号 | 2012081801001370 |
是否跨境货源 | 否 |
安装高度 | 6-12 |
等级 | 优级品 |
工作电压 | 24V |
类型 | 联网型 |
上市时间 | 2013年春 |
适用范围 | 仓库 |
探测距离 | 1400 |
销售方式 | 代销 |
颜色 | 黄色 |
重量 | 1kg |
品牌 | 海湾 |
型号 | JTY-HF-GST102 |
加工定制 | 是 |
打样周期 | 1-2天 |
质量认证 | CCC |
JTY-HF-GST102线型光束感烟火灾探测器(以下简称探测器)为非编码型反射式线型红外光束感烟探测器。该探测器必须与反射器配套使用,但需要根据二者间安装距离的不同决定使用一块或四块反射器。
I General
Conventional Beam Detector (hereinafter called the detector) is a non-
addressable infrared beam smoke detector, which must be used together with a
reflector. The number of reflector(s) to be used (one or four) depends on the
distance from the detector.
With excellent built-in microprocessor, the detector has strong ability of analysis and
judgment. The detector can automatically carry out system adjustment, compensation
of variation of ambient data, and judgment of fire and fault through fixed algorithm, and
indicate these states by LED and signal output terminals. With new and reasonable
design, attractive appearance, FLEXible adjustment and alignment method it’s easy to
install and adjust. The senSITIvity of the detector can be set through hand held
programmer in field, decreasing the demand for cleanliness of field
conditions, and enlarging application areas. The detector is applicable
to historical buildings, warehouses, large storages, shopping malls, leisure
centers, exhibition halls, hotel lobbies, printing houses, clothing factories,
museums and prisons etc, as well as places where slight smoke particles exist.
II Features
(1) Wide operating voltage range, big monitoring areas.
(2) Combination of the emitting and receiving part makes mounting easy and optical
pathway accurate.
(3) Built-in microprocessor enables intelligent judgment of fire alarm and fault.
(4) The detector can calibrate automatically, which ensures that one person complete
adjustment in short time. It’s also convenient to operate.
(5) Self-diagnosis function can monitor the inner fault.
(6) Automatic compensation for factors weakening received signals, such as dust
contamination, positional excursion and ageing transmitter.
(7) It has passive output contacts for fire alarm and fault.
(8) Two sensitivity levels can be set in field.
(9) The detector’s optical pathway is designed with strong anti-interference ability.
(10) SMT processing technology.
(11) Attractive and decent appearance.
III Technical Specifications
(1) Power Voltage: 15VDC to 28VDC
(2) Power Current: Commission current????20mA
Standby current????12mA Alarm
current????22mA
(3) Fire Alarm and Fault Contact Output:
Fire Alarm Relay: Contact capacity 28V/2A, which is normally open in normal state
Page 1
HD106
Conventional Beam Detector
Installation and Operation Manual
and closed in fire alarm state.
Fault Relay: Contact capacity 28V/2A, which is normally open in normal state and
closed in fault state.
(4) Angle of Adjusting: -6??to?+6?
(5) Sensitivity Level:
Level 1: High sensitivity.
Level 2: Medium sensitivity.
(6) Indication of Detector State:
Commission: Green LED and Yellow LED are lit or flash in a certain way. See
details in Section VI Commission.
Normal monitoring state: Red LED flashes periodically.
Fire: Red LED constantly illuminates, and Yellow LED turns off. Fire alarm should
be cleared through powering up again.
Fault: Yellow LED constantly illuminates. The detector clears the fault
signal automatically if the condition causing the fault disappears.
Optical pathway obscured totally: the detector first gives fault signal and turns
on Yellow LED. 20s later, it alarms fire, illuminates Red LED and turns off Yellow
LED. Note: In this case, it does not mean there is a fire. After the obscuration
is removed, the detector clears fault signal automatically. Fire signal has to
be cleared by powering up the detector again.
(7) Operating Environment:
Temperature: -10?C to +50?C
Relative Humidity: 95%, non condensing
(8) Monitoring Area: Maximum monitoring area: 1400m 2
Maximum width: 14m
(9) Length of Optical Pathway: 8m to 100m
(10) Protection Level:
Under common environment, ingress protection rating is IP20.
Under special environment, ingress protection rating is IP66 through
glue-seal treatment.
(11) Dimension: length: 206mm width: 95mm thickness: 95mm
(12) Material and Color of Enclosure: ABS, gray
(13) Weight: 450g
(14) Mounting Hole Spacing: Spacing for ding: 158mm
Spacings for surface mounting: 79mm to 96mm
¥210.00/个
面议
¥34.00/个
¥6500.00/个
¥99.00/个
¥3.50/个
¥220.00/个
¥1.00/个
¥1660.00/个
面议
本网页所展示的有关【4 wire Beam detector with relay output继电器光束烟感报警器】的信息/图片/参数等由的会员【 深圳市众安科电子有限公司 】提供,由智能装备网会员【 深圳市众安科电子有限公司 】自行对信息/图片/参数等的真实性、准确性和合法性负责,本平台(本网站)仅提供展示服务,交易前请与卖家联系,谨慎交易,因交易而产生的法律关系及法律纠纷由您自行协商解决,本平台(本网站)对此不承担任何责任。您在本网页可以浏览【4 wire Beam detector with relay output继电器光束烟感报警器】有关的信息/图片/价格等及提供 【4 wire Beam detector with relay output继电器光束烟感报警器】的商家公司简介、联系方式等信息。
在您的合法权益受到侵害时,请您致电0755-27219112,我们将竭诚为您服务,感谢您对智能装备网的关注与支持!
周一至周五 AM9:00 - PM18:00
积分充值:wei.z@wtmro.com
投诉建议:info@wtmro.com
扫码关注或加入QQ群(577347244)